Timing belt, water pump and crank seal replacement

I had some free time and decided it was time to replace some vital parts of a vehicle that I bought second hand.  These parts clocked the 100,000km mark so it's due for replacement. I have replaced these items before on some other vehicle make but I must say that Japanese cars are much easier as compared to  continental cars.

Before you start, it's a good ideal to have zip loc bags ready to keep and label all the bolts removed.  It will save you lots of time when putting back everything.  Ask me how I know.

Your car may be different from the description below but it will not be significant. Refer to your service manual. You need one weekend to do this job, long weekend is prefered.  I did this almost 1 year ago so some steps described may not be in the order done.

Prepare all the tools required.

Abbreviation used TB -timing belt, WP -water pump

First park the car on level ground and support the vehicle on car jacks. Choke the rear wheels and apply the hand brakes. Disconnect the battery terminals.

Remove the alternator and aircon belts. Loosen all the spark plugs

Dismantle the valve cover, protect  the overhead cams with a clean towel.

Undo the 3 bolts that attachs the pulley to the water pump. Remove the  TB plastic covers that protects the TB from contamination. The picture below shows the first half is removed and the lower half needs to be removed as well. There are usually 9 bolts that hold the 2 pieces of TB covers to the engine housing.

With the lower half of the TB plastic cover removed, the  full glory of the TB can be seen.

Next remove the crank shaft pulley center bolt. This one is super tight. Service manual recommends the use of a special tool to tackle this . There is another method. The electric starter itself is a powerful enough to undo the bolt. Arrange the breaker bar to bear against the drive shaft .When the engine is cranked, the bolt does not rotate and is loosen. This step requires the gear box to be in the neutral position otherwise something bad will happen. Reconnect battery terminals to use the starter  and undo the terminals when done.

Remove the crank shaft pulley to expose the crankshaft sprocket. The sprocket is a small toothed wheel that connects the TB. A woodruff key can be seen in the picture. Removing this key will loosen the crankshaft sprocket and expose a seal that needs to be changed.

Support the weight of the engine with a car jack and remove the right hand engine mount and bracket. The bracket gets in the way to remove the water pump . The bolts to the bracket are tight so use a cheater bar for leverage again.

I normally mark the position of the belt and pulleys with colored marker so that assembly will be a breeze. This method has proven to be the  best as compared to aligning the embossed arrows on the 3 pulley wheels at TDC ( top dead center) . Get to the  crank shaft pulley (temporary assemble back the pulley with the same bolt) and turn this pulley clockwise until the engine is at TDC. When the engine is rotated clockwise to the TDC, mark with colored marker the position of the timing belt relative to the 3  pulleys. the pulleys and TC are clearly marked with different color to prevent mistakes. The factiry has marking on the exhaust and intake sprocket to show when the engine is at TDC. usually the two arrows will pointing towards one another.

On the bottom left is the tensioner bearing, it keeps the belt tension in place and this needs to be replaced. The right hand side is also another bearing that needs to be replaced.  Usually the timing belt kit comes with all these parts. The belt goes around the intake and exhaust sprocket and also around at the bottom of the crank shaft sprocket.

 

Unhook the spring that is attached to the tensioner bearing and undo the center bolt to loosen the bearing. Now move the bearing away from the belt. The belt can now be removed with ease.

The bottom picture shows both bearings and belt removed. 

Get to the bottom of the car and remove the wooduff key and remove the crankshaft sprocket. You will be able to see a rubber seal . This is the crankshaft seal that seals the engine oil and needs to be replaced. I made a special tool to extract this piece of seal . Its very tight but care must be exercised not to marr or scratch the journal of the crankshaft. If its damaged, the crankshaft will have to be replaced.

Special tool in use. The triangle shape  is part of the timing belt marking.

 The seal is removed and journal inspected for deep scratches.

Replace with a new seal. Use the grease provided in the kit to ease the seal into its place. Tap it in squarely with a socket of a correct size diameter  PVC pipe

Remove the intake and exhaust sprocket and replace the seals as well. Two open enders are used to lock the cams in place to remove these two sprocket. the cams have a key way to accept the tools for lock down. Care must be taken not to damage the journal of the camshaft otherwise these have to be replaced. A note about the camshaft seals, they tight and removal might need a bit of struggle and swearing. Fitting in the new seals is exactly the same as the crankshaft seals

Right side replaced. Left side has no seal and awaiting for replacement.

Install the two sprocket back and torqued down to service manual specification.

Now drain the radiator of all its fluid and store it in a container. Dispose the fluid responsibly. Place a note on the steering saying" Top Up radiator fluid before starting engine.

Locate a black  O ring ( shown below) that needs to be replaced in the metal radiator hose that is part of the radiator hose. I had to to loosen the air con bracket that holds the air con compressor in place to access this O ring. 

Replace all radiator rubber hoses if there are signs of worn out. Undo the bolts that secure the water pump and pull out the mechanical pump. More radiator fluid will flow out and get ready to catch them under the car.

The old radiator gasket is probably  stuck and  needs to be removed by using a sharp razor  blade. Use fine grit sand paper to remove any remaining stubborn gasket.

Before installing the new pump,  compare the new pump with the old one and see any significant difference. Once satisfied, use Permatex Aviation Form A gasket sealant liquid to adhere the gasket to the the pump. I do not like to use sillicon gasket , these sillicon will give lots of issues later including clogging the cooling system. 

Apply the permatex sealant on both sides of the gasket and install the water pump. Torque down the bolts to specification.

Transfer the color marking done on the old TB to the new one. Install the new TB and align the colors marking of the TB to the color markings  on the 3 sprockets made earlier.

Install the TB  and it's two bearings. Hook the idle bearing spring in place and push the bearing against the TB slightly and tighten the bearing bolt to specification.  Tighten the other TB bearing bolt to specification.

Temporary install back the crankshaft pulley and turn the engine clockwise 2 times and check that the timing marks line up according to the service manual.  Once satified, install back the TB covers 

Install back the WP pulley and troque down. The crank shaft pulley bolt needs to be torqued down to 180 Nm ( needs to be very tight, it's the only thing that secures the pulley to the crankshaft ). Install back the 2 belts and all the other components  in reverse. Make sure there are no extra bolts left and all bolts are torqued down to specification. 

It's a good ideal to replace the valve cover gasket as well.  

Top up the radiator fluid and connect back  the spark plugs  and batteries terminals are the last to be connected.  

Before you start the engine, make sure all your tools are accounted for.